KR-55C can be used in "multi-out" mode, meaning that each instrument sound can be routed to separate outputs within a DAW virtual mixer. This is useful for individual panning, using third-party effects plugins, or routing to separate physical outputs of a multi-output audio interface.

The procedure for configuring multi outs varies depending on which DAW you're using, so you may need to consult your DAW's owners manual, or find a YouTube video where some windbag yabs about nothing for six minutes and explains the actual procedure in the last 12 seconds of the video (Invariably, this video begins with, "Hey guys...").

Regardless of which DAW you're using, when loading/opening the KR-55C instrument plug-in, select the KR-55C Multi Out version.

KR-55C Multi Out Configuration

Stereo Mix outputs 1-2 operate exactly the same as the standard stereo version of KR-55C, that is KR-55C's onboard mixer section controls and onboard effects will all operate as usual. We recommend turning the stereo mix DAW fader (the mixer channel with the KR-55C instrument) down to zero when using separate outputs, because mixing the instrument stereo outs with separate outs can get confusing.

The remaining individual instrument outputs are pre-mixer fader; in other words, they're unaffected by the onboard mixer's Level and Pan controls, and KR-55C's onboard effects are not applied. Though the individual outs will show as stereo pairs, all of KR-55C's individual instruments are inherently mono.

KR-55C Multi Out separate outputs are configured as follows:

STEREO MIX

1-2

BASS DRUM

3-4

SNARE

5-6

CYMBAL

7-8

HI-HAT

9-10

LOW TOM

11-12

HIGH TOM

17-18

LOW CONGA

19-20

HIGH CONGA

21-22

RIM SHOT

23-24

COWBELL

25-26

CLAVES

27-28

Using KR-55C Multi Out in Logic Pro

Configuring multi out instruments in most DAWs is relatively easy, but in their admirable quest to simplify easy tasks by wildly overcomplicating them, it's a little confusing in Logic.

Essentially, you'll need to create mixer auxiliary channel strips to route separate each separate output. An aux mixer channel is the same thing you'd use when adding a bus effect (for example, if you were routing multiple sources to a single reverb effect), but instead of setting the aux's input to a "bus" selection in its popup menu, you'll set it to one of KR-55C's individual audio outputs.

If you know your way around Logic's mixer, these can be configured manually, but Logic Track Mixer multi out instrument channel strips have an easy-to-overlook shortcut that simplifies the process.

For this example, we'll assume you're using the Logic Track Mixer, as opposed to the old-school Logic Environment Mixer.

Open an instance of KR-55C in a DAW instrument channel; make sure to select KR-55C Multi Out.

Open the Track Mixer either by clicking the mixer button in the top left of the menu strip (this may or may not be present depending on your Logic header setup), or with the top menu View>Show Mixer.

In the main KR-55C instrument mixer channel strip, click the + button beneath the output meter to add aux channel strips. Repeat this step for each separate out you'd like to use. It should look like the image below.

The aux channels default names will be something like Aux 1, Aux 2, etc.; in the image below, we've double-clicked and renamed them to match each instrument out.

The aux channel strips can now be used to individually set volume and panning, and third-party effects can be added either to the individual out aux channel strips, or by inserting effects to additional aux channels and using the individual out aux channel strip send knobs. This is the most flexible approach, because it allows independent volume and panning adjustment of dry and effect signals. Note that the although KR-55C's instruments are all inherently mono, the aux buses will show up in stereo. For best results, we recommend leaving them in stereo mode (otherwise panning can get kooky).

The aux channel inputs (i.e. instrument outputs) can also be reassigned by clicking the inputs buttons and selecting a different KR-55C source (i.e. instrument). We've added red bars around the input buttons in the image below:

We know the names are a little cryptic; unfortunately Logic doesn't let us give them custom names on the programming side. Below is a table showing each instrument and its seven-character Logic aux in selector name:

INSTRUMENT

LOGIC AUX BUS NAME

BASS DRUM

KR-53-4

SNARE

KR-55-6

CYMBAL

KR-57-8

HI-HAT

KR-9-10

LOW TOM

KR11-12

HIGH TOM

KR13-14

LOW CONGA

KR15-16

HIGH CONGA

KR17-18

RIM SHOT

KR19-20

COWBELL

KR21-22

CLAVES

KR23-24

Routing Instruments To Separate Audio Interface Physical Outputs

By default, all mixer channels and aux busses sum to Logic's master stereo outputs. To send KR-55C's individual outputs to separate physical outputs on a multi-out audio interface, click the Outputs buttons on the individual out aux channel strips (these will say St Out by default), scroll down, and select the desired Output or Bus destination.